Agreed, it seems logical that of all the containers I've tried, this one is the one that disabled L3HW offload. In this specific case, the only offloading I use is for fasttrack connections, so L3 shouldn't be interfering. I did submit a ticket and they said they've been able to reproduce the proble...

I submitted a support ticket with this, but I thought I'd bring it up here as well. Hopefully someone has a clever workaround. I'm attempting to run a DHCP server in a container on my CCR2116. I'd prefer to avoid having to do that, but Mikrotik's DHCP server doesn't do dynamic DNS updates and I alre...

I have 3 containers all set to start-on-boot. However, upon boot, the first one never auto starts, but the rest do. I'm seeing with with the 7.7 beta and RC. There are no log messages indicating any sort of failure to start either. I haven't tried 7.6 because I only have one device available for tes...

I can probably do it my creating my own Dockerfile/image Nope. It's set at container creation time, not baked into the image. I should've been more clear. I meant adding an IPv6 Address, not selecting a MAC address. That's what I do now, as soon as my container is first created, I add my manual IPv...

I'd like to use IPv6 with my containers and I'm running into an issue with non-deterministic IPv6 addresses. If I add an IPv6 prefix to my containers bridge and advertise it, my containers properly use SLAAC to get an IPv6 address, and I can then use that address for container communication. The iss...

It looks like the problem is somehow the SFP+ link between the CRS326 and the CRS309. I changed the link between the two from the SFP+ <--> SFP+ to CRS309 ether1 <--> CRS326 ether1 and my speed issues seem to have been resolved: CRS326 and CRS309 connected via SFP+ DAC: Speedtest by Ookla Server: Sp...

I tested with -R and it works as expected. ❯ iperf3 -c 172.16.10.1 Connecting to host 172.16.10.1, port 5201 [ 5] local 172.16.10.108 port 54558 connected to 172.16.10.1 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 114 MBytes 960 Mbits/sec 0 498 KBytes [ 5] 1.00-2.00 sec 11...

iperf works at 1Gbps, both to and from the firewall. CPU load on the firewall is negligible during either a full speed test through Connection 1 or through the slow test via Connection 2. I have no jumbo frames enabled anywhere in my network, and I've confirmed that in both CRS switch configs. Do yo...

I'm seeing low bandwidth (~250Mbps) when connected to a 1G RJ-45 port on my CRS326, but not when connected to the 10G SFP+ port. This low speed is only when going to the internet, I'm able to get the full 1Gbps to talk to my firewall/router via iperf3. Here's a poor diagram of my setup: Untitled Dia...

+ 1,就喜欢这个

I think we did chat on reddit, unfortunately changing my ND options doesn't seem to have an effect. I've tried changing multiple different settings, disabling/enable IPv6, deleting/recreating the DHCP client settings, etc and for some reason, the Tik can't seem to get an IPv6 address. 24 hours later...

I just got an RB4011 and got it setup per these instructions perfectly (using the supplicant method). Now I'm attempting to get an IPv6 address and it's just not happening. This is my entire IPv6 config right now: # jun/02/2020 17:01:27 by RouterOS 6.47 # software id = 168G-AZKL # # model = RB4011iG...