Sim-card lost after upgrading.
v6.47

v6.45.9

I have several 4G devices which I normally restart through SMS when needed, for instance when VPN is disconnected and does not reconnect on its own. Yesterday, I received a proposal to an idea where I can use netwatch so that the device automatically restarts within 10 minutes when internet connecti...

Hi,
I,m getting a very unreadable message. Any idea? CCR1016-12S-1S+

Hi, I have two different networks 192.169.200.0/24 and 172.16.0.0/24 which are isolated from each other. I want to allow 3 devices in the first network to be able to reach the other network - with a little bit security -not depending on IP or mac address but depending on windows AD server which is i...

I understand that I will need a guest VLAN, but how can I have two passwords for the same SSID, where each password determines which VLAN the client connects to?
//Nizar

你好,这是在所有可能的一个名称but have more then one password associated with it? I ask because the idea came about of have a way for guest to access our wifi so they can get internet, but not be able to access our network. I mean that if it's possible that the password is the o...

I'm using an Aerohive AP Wait, does that device even support powering using Passive POE? I can see it supporting active POE over mode A, not passive/mode B. Maybe it does but only using 100Mbit but can't find anything about it being officially supported for your device. There is a difference betwee...

I'm using an Aerohive AP

Yes, I'm using POE out !!

Hello,
I've just got my first RB4011 and it works fine except the port 10 which is POE port, wich give the rate of 10Mbps with POE
any idea..
Nizar

Thanks a lot !! this was the missing point

I did try this but in this case the MT lose the connection with server.

Have you tried to downgrade sys to 6.39.3 ??

Hello! I have just got an CRS317 and tried to config it as a router to my office, the configuration looks like this: # model = CRS317-1G-16S+ /interface bridge add admin-mac=64:D1:54:EA:BB:71 auto-mac=no fast-forward=no name=bridge1 pvid=1 vlan-filtering=yes /interface vlan add interface=sfp-sfpplus...

Yes I can, but the question is why I'm loosing mikrotik every time I try to update it.
Is it just me who face this problem?

Every time I try to update my Mikrotik access point (wAP ac and hAP ac lite tower) to the current 6,41 i lose the connection, the AP is just trying to restart and i have to netinstall it again.
Any idea

Hello.. I'm running CHR on VMWARE, with licens P10, I'm having an issue when using a vmxnet3 network card, the card shows up as 10Gbps but says "incompatible". Now, despite that not having a direct performance impact on the interface, and being able to get 10Gbps just fine. There seems to ...

Hello.. I'm having the same issue and despite not having a performance impact on the interface, There seems to be an issue with DHCP when running on a bridge. When an interface is slave to a bridge it seems that it doesn't respond to DHCP client requests. I cannot get an IP from DHCP when on bridge....

Hello, I'm trying to make EoIP this way: Ritning1.jpg The EoIP tunnel works fine and in my case I would rather have all offices to be in the same network that's why I used EoIP, but at the same time, each office should be able to surf on its own internet as if not to use the internet from Office 1 t...

Hi,
I'm trying to make a GRE tunnel between two office, and it works, the problem i got that i must have the same subnet in both sides, which means same one DHCP server and same network in the both sides.
It works with EiOP tunnel but I wold se if it should works too with GRE.
Any idea?

Hey skuykend.... Yes I think the problem is exactly as you said VLAN2001 is tagged and untagged in the same port :) this was a big mistake of mine. Thank you. For one, it looks like port Ether1 is messed up, you're tagging the output of all your vlans to Ether1 (even though most aren't in the vlan t...

Hey mariuslazar I didn't have a very simple project in my CRS :) it has many VLAN 1 Hybrid port (1 untagg and 8 tagg) and 2 port trunk (tagg only) the other ports are access port. All vlan are in the same switch, I putt them in unused port becouse I have tow internet sources from tow ISP and I need ...

actually I configure my CRS in this way and it works fine. /interface ethernet switch vlan add ports=“ether1,ether2,ether3,ether4,ether5,ether6,ether9,ether10,ether11,ether12,ether13” vlan-id=11 add ports=ether1,ether3,ether4,ether5,ether6,ether17,ether18,ether19,ether20 vlan-id=21 /interface ethern...

Hi I'm trying to configurate my CRS with tagged and unntagged vlan, and I'm facing a loop problem, witch i did not understand where this loop is in my configuration. Can any expert here see and help me with this? interface ethernet set [ find default-name=ether1 ] master-port=sfpplus2 set [ find def...

Hi, your problem is easy as this:

/ip firewall filter
add action=fasttrack-connection chain=forward disabled=no

Hello all.. I wold like to thank you for helping me. I've just found a perfect solution and get a perfect result in speed test: it was just to add: /ip firewall filter add action=fasttrack-connection chain=forward And my new configuration look like this: /interface ethernet set [ find default-name=e...

Hi,
Thanks for your replay,
Yes it think so toonatting causing the issues,
Fierwall 54%
networking 32%
ethernet 12%
:? :? :( :( :(

Hi It's my first time using a Mikrotik switch, and i'm facing a big problem with it. Our company usually uses HP1920 as a router switch but since HP1920 was designed for 256 arp routing, we decided to use Mikrotik CRS226-24G-25+RM. The issue i'm currently having is that the cpu hits high load leve...