社区讨论
．.还VxLAN
我需要做的是连接LAN 1和LAN 2，这样每个网络上的设备都可以看到对方，并且能够从任何一侧进入两个路由器配置。
我解释的问题/图表比前三个帖子更字面。 所以你能解释一下这两个路由器是否在同一栋楼里，并且连接两个路由器的LAN 1的看起来像电线的是物理cat 5链路吗? 因为如果是这样的话，我认为任何形式的VPN都不是最好的解决方案。 至少也要提供所涉及的两台路由器的品牌和型号。您有了一个很好的图表(尽管知道应该指定连接路由器的端口)。 事实上，如果你想要好的建议，你应该参考下面的建议。 得到的答案和如何有效地报告bug @anav的新用户发帖寻求帮助 充分利用这个论坛
同一栋楼里有2台RB951G-2HnD。——剪断我之所以这样设置是因为我在LAN1和LAN 2中运行了一些应用程序，这些应用程序需要具有不同的公共IP。
．.还VxLAN …还有VxLAN和ZeroTier。(ZeroTier包括提供所需的第3台路由器) 在某些情况下，MPLS/VPLS是EoIP的已知替代品。
隧道近终点(AP)在WinBox中，首先单击MPLS按钮。首先，您必须通过单击“LDP设置”按钮并启用LDP来打开LDP。翻译成ROS7: Create LDP Instance。LSR ID = AP IP地址路径向量限制= 255跳数限制= 255在“LDP接口”页签中单击加号。选择我们将在其上创建隧道的接口(在本例中为wlan1)和传输IP地址(该路由器的wlan1 IP 10.0.0.1)，然后单击OK。在“LDP接口”页签中单击“加号”。选择我们要在其上创建隧道的接口，在本例中为wlan1，传输IP地址为该路由器的wlan1 IP 10.0.0.1，设置Hello间隔为00:00:05，保持时间为00:00:15，勾选“接受动态邻居”，单击“确定”。注意:“接受动态邻居”是默认不勾选在ROS7。 The rest is unchanged: 3. In WinBox, click the MPLS button and select the VPLS submenu button and on the VPLS tab click the plus sign. Set the Remote Peer to the IP address of the remote end’s wlan1 interface, in this example, 10.0.0.2. Set the VPLS ID to the default of 0:0 and click OK. 4. Create a new bridge interface by clicking the Bridge button and the plus sign and OK. 5. On the bridge ports tab, click the plus sign and add the LAN interface, in this case ether1. Click the plus sign again and add the vpls1 interface you just created and click OK. Far End of Tunnel (station) 1. In WinBox, begin by clicking the MPLS button. First you must turn LDP on by clicking the LDP Settings button and enabling LDP. With the same translations for ROS7 1 Create LDP Instance . LSR ID = AP IP address Path Vector Limit = 255 Hop Limit = 255 2. On the LDP interface tab click the plus sign. Select the interface on which we will create the tunnel, in this case wlan1 and the transport IP address which is the public IP of this router, 10.0.0.2 and click OK. Same translation as before for ROS7: On the LDP interface tab click the plus sign. Select the interface on which we will create the tunnel, in this case wlan1 and the transport IP address which is the wlan1 IP of this router, 10.0.0.2 , set Hello Interval to 00:00:05, Hold Time to 00:00:15, tick the "Accept Dynamic Neighbors" and and click OK. Attention: "Accept Dynamic Neighbors" is default not ticked in ROS7. The rest is again unchanged: 3. In WinBox, click the VPLS button and on the VPLS tab click the plus sign. Set the Remote Peer to the IP address of the remote end’s public interface, in this example 10.0.0.1. Set the VPLS ID to the default of 0:0 and click OK. 4. Create a new bridge interface by clicking the Bridge button and the plus sign and OK. 5. On the bridge ports tab, click the plus sign and add the LAN interface, in this case, ether1. Click the plus sign again and add the vpls1 interface you just created and click OK. The two LANS are now bridged using VPLS. To confirm that LDP is running, click the MPLS button and then the LDP Neighbor tab. You should see the other end of the tunnel displayed. To confirm that the VPLS tunnel is running, click the Interfaces button, double click the new VPLS interface, and check the status tab. You should see a display of the tunnel details.